In development

CommVoy Unit

The four-seat in-vehicle intercom. Four wired headsets, your two-way radio with push-to-talk, music, Wi-Fi and GPS, in one extruded aluminium box.

The CommVoy Unit from the front left: three machined knobs, status and seat lights, and the CommVoy logo etched on the side of the aluminium case.

The front

Three knobs. Seven lights.

The common settings are on the knobs, so nobody needs a phone while driving.

  1. Volume Headset volume for every seat. Hold the knob to set one seat at a time.
  2. Music Music level. Press to mute.
  3. Squelch How easily the mics open on speech. Hold to set one seat at a time.
  4. Status Green when running, a red blink on a fault, yellow when a mic overloads.
  5. Radio Blue while the radio is receiving.
  6. TX Red while you transmit on the radio.
  7. Seats 1–4 Lit while that seat's mic is open, so you can see who is talking.

CommVoy Unit In development

Four headsets. One radio. Every vehicle.

It connects the crew's wired headsets, your two-way radio and push-to-talk buttons, with Wi-Fi and GPS inside.

  1. Front

    Three knobs: volume, music and squelch. Seven lights: status, radio, transmit and one for each seat.

  2. Case

    Extruded aluminium, 150 × 106 × 55 mm, with a screwed plate at each end.

  3. Rear

    Four 5-pin headset sockets: driver, co-driver, right rear, left rear. Radio, 12 V and push-to-talk on one harness. Wi-Fi and GPS antennas, and a 3.5 mm music input.

The unit from the side: the extruded aluminium case with the CommVoy logo and a topographic pattern etched along its side.
Front: three knobs and seven status lights. Case: extruded aluminium, 150 × 106 × 55 mm.
The rear of the unit: four 5-pin headset sockets labelled 1 Driver, 2 Co-driver, 3 Right rear, 4 Left rear, gold Wi-Fi and GPS antenna sockets, a stereo jack and the radio harness grommet.
Rear: four 5-pin headset sockets, radio / 12 V / PTT harness, Wi-Fi and GPS antennas, music in.

The back

Every connection, labelled.

Headsets on the top row. Antennas, music and the vehicle harness below.

  1. Driver 5-pin headset socket, seat 1. Its push-to-talk keys the radio.
  2. Co-driver 5-pin headset socket, seat 2, with its own push-to-talk.
  3. Right rear 5-pin headset socket, seat 3. Intercom only.
  4. Left rear 5-pin headset socket, seat 4. Intercom only.
  5. Wi-Fi Antenna socket (SMA). The unit's own settings network, and internet for CommVoy channels.
  6. Stereo 3.5 mm music input from a phone, a Bluetooth receiver or any player. Played in mono to both ears in every headset.
  7. Radio / 12 V / PTT One harness: vehicle power, the radio's audio both ways, its push-to-talk, and the two push-to-talk buttons.
  8. AUX A spare grommet for extras, such as power for wireless headset packs.
  9. GPS Antenna socket (SMA) for an active GPS antenna.

Intercom and headsets

Four seats, each tuned to its headset.

Everyone hears everyone, hands-free. Each seat has its own listening volume, mic boost and squelch, and its own mic type: dynamic, or electret with power from the unit. So the off-road headsets and helmet kits riders already own plug straight in, including generic ones, as long as they use the common 5-pin wiring.

Which headsets work →

  • 45-pin headset sockets
  • 0–42 dBmic boost, per seat
  • 2mic types: dynamic or electret
  • Per seatvolume, squelch, noise reduction

Smart voice squelch

Voices in. Engine, wind and road noise out.

The intercom opens for the person talking and stays quiet for engine, wind, road noise and bumps. That means very few accidental openings and no constant hiss in everyone's ears, between words and between conversations. Each seat is tuned for its own headset.

  • Talk normally: it opens quickly for your voice at a normal speaking level, so nobody has to yell over the engine to be heard
  • Quiet between words, and the start of what you say comes through
  • Noise reduction and squelch set for each seat
  • Music dips under voice and comes back after
  • What you say on the radio goes out complete
Noisy cab
What the crew hears
Illustration, not a measurement.

Radio

No squelch tails. No key-up hiss. Just the voice.

Clean radio audio: you hear the voice, not the noise. No burst of static when someone keys up, no squelch tail when they let go, and nothing cut out between their words. For radios run with open squelch it can be switched off.

One harness connects the radio's speaker output, its mic input and its push-to-talk. The radio side is isolated from the vehicle with transformers and an optocoupler, which keeps alternator whine out.

  • Works with the two-way radio in your vehicle; everyone hears incoming calls, and music dips for them
  • Driver and co-driver each have a push-to-talk; only the person holding it goes out on air
  • Choose whether the crew hears the person transmitting, or the car goes quiet while you are on air
  • Stuck-button cut-off, so a jammed push-to-talk does not keep the radio keyed
  • Each push-to-talk can go to the radio, to your CommVoy channel, or one of each

Position over radio

Every key-up puts you on the map. No cell service needed.

When you release the push-to-talk, the unit can send a short burst with its GPS position over the same radio. Every CommVoy unit that hears it decodes it, as far as your radio reaches, so the vehicles you talk to keep showing where you are, out where phones have no signal.

  • Heard vehicles show with distance and direction on any phone joined to the unit's Wi-Fi
  • With internet and relay switched on, they also appear on the CommVoy app map for your whole channel
  • Send after every transmission, or at most once every 15 seconds to 10 minutes
  • Received bursts are muted in the headsets: nobody hears the data
  • Plain APRS format, or private mode that scrambles the position with your group's code

Data bursts and scrambled transmissions are not allowed on every radio service. Use them only where your radio licence and its rules allow; see the terms.

A B C D A keys up
Illustration. A transmits; B, C and D hear the call and see A move from its last position to the new one.

Beacons

Everyone on the map, whatever they carry.

With the app or a unit

Every vehicle in the group.

Phones with the CommVoy app share their position with your channel over the internet when there is signal. CommVoy units share theirs over the vehicle radio on every key-up when there is not, as far as your radio reaches.

CommVoy beacons Coming

For vehicles without the app.

A small CommVoy beacon puts a vehicle on the map even if nobody in it runs the app. Beacons reach up to 5 miles between vehicles in open terrain, and every beacon relays for the others, so the convoy covers more ground and stays on the map, even with no cell service.

Range depends on terrain and where the beacon is mounted; hills, canyons and mounting inside the vehicle reduce it.

What's coming

More ways in.

Settings

Programmable from your phone.

The knobs handle volume, music and squelch on the move. Everything else is set from the unit's own settings menu: join its Wi-Fi with your phone, or use the Unit tab in the CommVoy app once paired. Settings are saved in the unit, which then works with no phone at all.

  • Mic boost for each seat, with a live level meter
  • Noise reduction for each seat, from light to strong
  • Mic power on or off per seat, for electret or dynamic mics
  • Squelch sensitivity for each seat
  • Listening volume for each seat
  • Radio levels and clean radio audio on or off
  • How far the music dips for talk and for the radio
  • Where each push-to-talk goes: radio, internet channel, or split
  • Position over radio: when to send, callsign, plain or private
  • Trip logging and recording to the memory card
  • Stuck push-to-talk timeout and light brightness

A paired app can change settings. It cannot open a microphone or key the radio: only the push-to-talk buttons can.

Specifications

What is in the design.

Taken from the hardware and firmware design of the prototype. Details can change before the unit is offered.

Seats4 wired headset sockets, 5-pin: driver, co-driver, right rear, left rear
Headset wiring1 mic − / ground, 2 push-to-talk (seats 1 and 2), 3 mic +, 4 speaker +, 5 speaker −
MicrophonesDynamic or electret, chosen per seat. Mic gain 0 to 42 dB per seat. Paired or single-wire mic wiring per seat
Per seatListening volume, mic gain, squelch sensitivity, noise reduction
IntercomHands-free; everyone hears everyone
Two-way radioReceive audio, transmit audio and radio key, isolated from the vehicle (transformers and an optocoupler)
Push-to-talk2 inputs, driver and co-driver. Each can key the radio or talk to your CommVoy channel
MusicLine input on a 3.5 mm stereo jack, played in mono to both ears. Dips for talk and for the radio, muted while transmitting
Radio audioClean radio audio: no squelch tails, no key-up static
Intercom squelchSmart voice squelch, tuned per seat: opens for the person talking, stays quiet for engine, wind and road noise
Controls3 knobs, push to click: volume, music, squelch
Lights7: status, radio receive, transmit, seats 1 to 4
Wi-FiThe unit's own network for its settings page; joins a Wi-Fi network with internet for CommVoy channels. Antenna socket (SMA)
GPSBuilt in, with an antenna socket (SMA) for an active GPS antenna
Position over radioOptional short position burst after you release talk, plain or private (group code)
Wireless headsetsSupport for up to 4 CommVoy wireless headset packs (in design)
RecordingOptional recording to a microSD card inside the unit, for setup and testing
Power12 V vehicle supply: fused, reverse-polarity and surge protected, isolated converter against alternator whine
CaseExtruded aluminium, 150 × 106 × 55 mm outside

Installation

One box, one harness.

An overview of what an install involves. Step-by-step instructions will come with the unit.

  1. 1

    Mount it

    Somewhere the driver and co-driver can reach the knobs. Mounting hardware will be specified with the first units.

  2. 2

    Power

    Fused 12 V and ground from the vehicle, through the harness.

  3. 3

    Radio

    The same harness connects to your radio's speaker output and mic socket, plus the two push-to-talk buttons.

  4. 4

    Antennas

    GPS antenna where it can see the sky; Wi-Fi antenna on its socket at the back.

  5. 5

    Headsets

    Plug each seat's 5-pin headset cable into its socket: 1 driver, 2 co-driver, 3 right rear, 4 left rear.

  6. 6

    Set up

    Join the unit's Wi-Fi from your phone, set mic types and levels, and you are done.

In the box Planned, not final

  • CommVoy Unit
  • Wi-Fi antenna and GPS antenna
  • Radio / 12 V / push-to-talk harness

Radio adapters, push-to-talk buttons and headsets depend on your vehicle and radio. We will confirm the contents before the unit is offered.

Close-up of the faceplate: machined aluminium knobs with a single amber index line, small etched legends, and lit status and seat lights.

Faceplate

Black Ridge.

Bead-blasted black anodised aluminium, a bright diamond-cut edge, and only what you need on it: small, wide-tracked laser-etched legends on two clean rows, and one amber mark. Machined aluminium knobs, 20 mm, with a fine knurl on the grip and a single amber index line.

  • Plate6061 aluminium, black anodised
  • LegendsLaser etched, one baseline per row
  • Knobs20 mm machined aluminium
  • MarkOne, engraved and amber filled
  • EdgeDiamond-cut chamfer
  • LightsFlush light pipes

Renders of a concept finish. The prototype's end plates are black circuit board with white lettering.

The same unit with a gunmetal grey faceplate.
Also explored: gunmetal plate with dark-filled legends.
The back of the unit: four 5-pin headset sockets numbered 1 to 4 in amber, gold Wi-Fi and GPS antenna sockets, a stereo jack and the harness grommet.
The back plate in the same finish, seat numbers in amber.

Unit questions

When can I get one, and what will it cost?

We do not have a date or a price yet. The unit is a working design at the prototype stage. Join the early list to hear first.

Does it work without the app or a phone?

Yes. Intercom, radio and music run on the unit alone, and its settings are saved in it. A phone is only needed to change the less common settings, or to talk to your group over the internet.

Can the back seats talk on the radio?

No, by design. The two push-to-talk inputs belong to the driver and co-driver. The rear seats are on the intercom and hear the radio.

Can someone listen in through the app?

No. A paired app can change settings, but it cannot open a microphone or key the radio. Only the push-to-talk buttons send audio out of the vehicle.

Is it waterproof?

We make no waterproofing or dust rating claim. The design aims to keep dust out: the case has no USB opening, and every connector is on the back plate.

Can I use only two seats?

Yes. Plug in as many headsets as you have; unused seats stay quiet.

Be first in line.

The CommVoy Unit is in development. Join the early list and we will tell you when units, wireless packs and headsets are ready. Joining is free and commits you to nothing: no order, no payment.

Opens an email to [email protected] with a short form: your vehicle, seats, headsets and radio.